Price list ( Length Measurement )  
Description
Charges US$ each
Description
Charges US$ each
Outside Micrometers
25
Bore Gauge Without Dial Gauge (Transmission only)
25
a
 Upto 100 mm/Upto 4"
25
Dial Thickness Gauge
25
b
 200 to 300 mm / 8 - 12"
25
Mikrokator Dial Gauge
c
 300 to 600 mm / 12 - 24"
25
a
 L.C. 0.001 mm
25
d
 600 to 1000 mm/24 - 40"
65
b
 L.C. 0.0005 mm
45
e
 1000 to 1500 mm/40 - 60"
99
c
 L.C. 0.0002 mm
55
f
 Setting Rod upto 300 mm/12"
25
Plain Plug Gauges upto 250 mm
25
g
 Setting Rod upto 1000 mm/40"
25
Width Gauge
25
h
 Setting Rod upto 1500 mm/60"
35
O.D. Master
25
i
 Please Note : Calibration of One Setting Rod
Steel Ball
25
j
 Free with concerned Micrometer
Step Gauge (Upto 100 mm) (per step)
25
Depth Micrometer
Measuring Pin (0 - 20 mm) Min. Length 35 mm
25
a
 0 - 100 mm
25
a
 (Per Pin) if minimum Quantity10Nos.
3
b
 100 – 200 mm
25
Measuring Tapes/Steel Scales
c
 200 – 300 mm
25
a
 1 Meter - 10 Readings
25
d
 Setting Rod upto 300 mm/12"
25
b
 Above 1 Meter - Each 1 Meter Step
2.5
e
 Please Note : Calibration of One Setting Rod
Snap Gauge
f
 Free with concerned Micrometer
a
 Upto 150 mm
25
Inside Micrometer
b
 Upto 300 mm
25
a
 Up to - 100 mm
25
c
 And above
35
b
 100 – 200 mm
25
For special gauge
25
c
 200 – 300 mm
25
Dial Snap Gauge
d
 Setting Rod upto 300 mm / 12"
25
a
 L.C. 0.01 mm
25
e
 Please Note : Calibration of One Setting Rod
b
 L.C. 0.002 mm
35
f
 Free with concerned Micrometer
Square Cylinder
Thread Pitch Micrometer upto 100 mm
25
a
 Range upto 300 mm
185
a
 Setting Pc. If any
25
b
 Above 300 mm & upto 600 mm
205
b
 Pair of Thread Pitch Anvils
25
Height Master (Height Micrometer)
Passometer (Upto 100 mm)
25
a
 Range upto 300 mm
205
A. Vernier Calipers
Uni Master
495
a
 0 - 150 mm/6"
25
Feeler Gauges (For four feeler gauges)
25
b
 0 - 200 mm/8"
25
a
 more than four feeler gauges per each feeler
2.5
c
 0 - 300 mm/12"
25
Foil each
25
d
 0 - 450 mm/18"
25
Sheet Thickness Gauge/Wire Gauge(Per Hole/Per Gap)
25
e
 0 - 600 mm/24"
25
Hegman Gauge (Per Point)
25
f
 0 – 1000 mm/40"
65
Comparator Stand
25
g
 0 – 1500 mm/59"
99
Tri-Square
25
B
 . Dial/Digital Vernier
Dial Calibration Tester L.C. 0.001 mm
99
a
 0 - 300 mm/12"
25
Electronic Dial Calibration Tester L.C. 0.0001 mm
b
 0 - 600 mm/24"
35
a
 Upto 25 mm
300
c
 0 - 1000 mm/40"
65
Linear Probe GT 21(Per Scale & Per L. C.)
C
 Depth Vernier
a
 i. L.C. 1 µm
185
a
 0 - 150 mm
25
b
 ii. L.C. 0.1 µm
185
b
 0 - 200 mm
25
c
 iii. L.C. 0.01 µm
185
c
 0 - 300 mm
25
d
 Sylvac Probe 10 mm (P 10 + DRO D 80)
185
D.
Depth Dial Vernier 0 - 300 mm
25
e
 Sylvac Probe 25 mm (P 25 + DRO D 80)
400
E.
 Dial Caliper (Inside)
25
Squareness checking Fixture
25
F.
 Dial Caliper (Outside)
25
Pistol Caliper
25
Vernier Height Gauges
Pie (O.D. Measuring) Tape up to 500 mm
25
a
 0 - 300 mm/12"
25
a
 Pie (O.D. Measuring) Tape up to 1000 mm
25
b
 0 - 450 mm/18"
35
Caliper Checker
c
 0 - 600 mm/24"
45
a
 Upto 300 mm
205
d
 0 - 1000 mm/40"
65
b
 Upto 600 mm
300
e
 0 - 1500 mm/59"
99
Ring Gauges for Go & Nogo Charges are separate
A. Plunger Type Dial Gauges
a
 0-100 mm
25
a
 L.C. 0.01 mm/0.001"
25
b
 100-200 mm
25
b
 (Travel above 10 mm - Per 10 mm)
25
Thread Ring Gauge( For effective pitch diameter only.)
c
 L.C. 0.002 mm/0.0001" (Travel - 1 mm)
25
a
 0-100 mm for Go & Nogo Charges are separate
25
d
 L.C. 0.001 mm/0.00005" (Travel – 1 mm)
25
b
 100-200 mm
100-200 mm
e
 (Travel above 1 mm)
35
Thread Plug Gauge (For effective pitch diameter only)
B.
Lever Type Dial Gauges
a
 0-100 mm
25
a
 L.C. 0.01 mm/0.001"
25
b
 100-200 mm
25
b
 L.C. 0.002 mm/0.0001"
25
Ford cup
25
c
 L.C. 0.001 mm/0.00005"
25
Test Sieves
25
Slip Gauges (Metric)
(As per IS. :2984)
Bevel Protractor
25
A.
 Inspection Grade/Workshop Grade per Slip
2.5
Combination Set
25
a
 0 Grade by comparison Method per slip
2.5
V' Block
35
B.
 Special Large Slips Above 100 mm & Upto 500 mm
25
Radius Gauge
65
a
 per slip
Pitch Gauge
65
b
 Special Small Slips per slip
25
Glass Scale 100 mm
25
c
 Length Master upto 300 mm
25
 
Bore Gauge With Dial Gauge (Transmission only.)
35
 

Terms of Business :
1
 Calibration will be done as per our procedure.
2
 For at site Calibration Following charges to be added –
 
i
 To and Fro Traveling .
ii
 Lodging, Boarding and Local Conveyance to be arranged by you.
iii
 Handling Charges extra at actual.
3
 For before and after calibration (AS Per QS requirement) 40% will be charged extra on Prices quotated.
 
TERMS AND CONDITIONS FOR FOREIGN CLIENTS.
TRACEABILITY : Calibration Certificate issued by us establish Traceability to
National/International Standards.
DELIVERY : Within weeks time.
DEMURRAGE : If the instruments are not collected within 30 days from the date of
Proforma Invoice, the demmurage will be Charged @ 5% Per
week per Consignment. 100 % against Proforma Invoice
PAYMENT : 100 % against Proforma Invoice Through Bank T/T
MATERIAL HANDLING :

Extra at actuals. We do not hold ourselves responsible for any

damage/loss after the goods are delivered to your
Representative/Transporter/Courier.

INSURANCE : To and Fro by you. All transit risks are to your A/C.
CUSTOM DUTY : Octroi duty is applicable, @ 5% on the declared value of your
instruments. Please note that we are not responsible for hold-up
instruments at the limits of Pune Municipal Corporation, because of
incomplete documents with the consignment for Octroi clearance
at Pune.
TAXES & DUTIES : Extra as applicable.
JURISDICTION : All disputes subject to Pune India Jurisdiction.